What’s New on this Site?
Here’s a summary of the latest things that have been added to or changed. Bookmark this page so you can check back now and then. It’s a quick way to see what has been added since the last time you looked at Sherline’s site. Don’t forget to refresh the page to be sure you are getting the latest version.
NEW PRODUCTS! (November 2018)
Ball Screw Mills
CLICK HERE to enter the category
Our new ball screw mills can be purchased with 12″, 14″, or 18″ bases, and come in CNC-ready or full CNC configurations. Low friction in ball screws yields high mechanical efficiency compared to other leadscrew alternatives, and efficiencies can range from 70% to 95%.
Key upgrade parts for these ball screw mills include:
- Ball leadscrews
- High-torque stepper-motor couplings
- Ball screw mill saddle (nickel/Teflon plated) for the X/Y-axes
- Vertical milling column saddle for ball screws
- Column saddle Z-axis ball nut mount for the Z-axis
- Linux CNC program disc designed specifically for ball screws
NEW PRODUCT! (November 2018)
Laser-Engraving Pin Chuck Jaws
Our new laser-engraving pin chuck jaws were developed as a result of requests from our laser marking customers who wanted increased holding diameters. The jaw tops are flat, which gives you a surface to locate your parts against. The short pin jaws (P/N 11414L) can hold round parts up to 3.7″ (94mm) OD and as small as .54″ (13.7mm) ID, while the extended pin jaws (P/N 11413L) can hold parts up to 6″ (153mm) OD and as small as .66″ (16.7mm) ID. The extended jaws are made up of a set of hardened master jaws and extended top jaws.
Each set of jaws has three pin hole locations that hold 3/16″ hard-steel dowel pins, and the pins come in 1″ and 1.5″ lengths, both in sets of three. These thicker 3/16″ pins are for heavier industrial usage.
*NOTE: These jaws are not designed for machining parts or other uses that require more than finger tight closing pressure to hold the part in the chuck.
NEW PRODUCT! (October 2018)
Electroless Nickel Plated Spindle Headstock P/N 30101
Customers have often asked if we will ever offer a stainless steel spindle in our headstocks. The short answer is, “No.” However, we are now producing a spindle based on our standard headstock that has an Electroless Nickel Plated Spindle with a 3/4″ x 16 T.P.I. This coating offers a hard surface that is rustproof. We believe that this is a cost-effective alternative to using stainless steel. The spindle is available separately, in a headstock, or with a full headstock and motor assembly.
NEW PRODUCT! (June 2018)
Split Bed Pool-Cue Lathe P/N 7000
We are now offering a Split Bed Pool-Cue Lathe, in addition to our custom Extended Bed Lathe. This Split Bed Lathe setup allows custom pool cue makers the ability to adjust the distance between the headstock and the tailstock, depending on the length of the stock being turned, without the expense of ordering a custom extended lathe bed (includes everything you see in the photo). CLICK HERE to learn more about our Custom Lathes and Tools for Turning Pool Cues.
Our updated website has all the great information you have become accustomed to, but it now includes an online store, a new shipping calculator, an improved search function, streamlined menus, and simplified navigation.
Due to the transfer of the online store, you will have to create a new user account and will no longer have access to your prior order history on Sherline Direct. If you have any questions regarding new account creation or your previous order history, we will, of course, be more than happy to help.
The 3C lever collet closer was designed to work with our 3C headstock (P/N 30113) and is based on the same design as our standard lever collet closer (P/N 1150). It has separate mounting bases that attach to our standard lathes (P/N 4000 and 4400 models), and our industrial chucker lathe (P/N 6600 models).
Anyone doing repetitive lathe operations on small parts will find this new accessory saves a lot of time when holding parts in a 3C collet.
We also offer an optional material stop (P/N 3024) for the 3C lever collet closer.
Ball Screw X/Y Saddle Lubrication Update
The first few ball screw machines we sent out had an issue with the lubrication system on the X/Y saddle. The oil will immediately drain out of the saddle rather than slowly lubricating the Y-axis dovetail. This video shows how to solve the problem with a simple fix.
CLICK HERE to view the YouTube Video
We are proud to announce the introduction of ball screw retrofit kits for the X/Y and Z-axes for our mills (Series 5400, 2000, and 5800 models).
The key upgrade parts for this ball screw retrofit kit include ball leadscrews, stepper-motor coupling, the ball screw mill saddle (with nickel/Teflon plate) for the X/Y-axes, a vertical milling column saddle for ball screws and column saddle Z-axis ball nut mount for the Z-axis.
You can order the kits and install them yourself, or you can ship your machine to us for a factory install (installation charges will apply).
These retrofit kits also complement our new High-Torque Stepper Motors (P/N 67127).
NEW WEB PAGE (January 2018)
We have created a new web page devoted to ship modelers. This page highlights the various machines that Sherline offers that can help model makers take their skills to a higher level.
The page also shows typical projects that a show the types of items that can be created using miniature machine tools like wheels, block and tackle, and many other small fittings.
We also feature some master model builders who create museum quality ship models. You can visit their in-depth bios using links to The Miniature Engineering Craftsmanship Museum website.
NEW PRODUCT! (January 2018)
3/8″ Chuck Arbor with 3/8″ Shank P/N 11850
This chuck arbor was designed to mount 3/8″ drill chucks in our multi-tool holder tool posts that have a 3/8″ hole. These tool posts include the following:
NEW PRODUCTS (November 2017)
High-Torque Stepper Motors P/N 67126
Our new, high-torque stepper motor has the same NEMA #23 frame as our standard stepper motor, but it has over 75% more torque. The increased torque means that you can increase your feed rates, and it is also better suited to handle the additional weight of the motor and headstock on our Z-axis.
The high-torque stepper motors can also be used on any Sherline CNC machine. The motor is 2 amps, just like our standard motors, so you can easily upgrade your current Sherline system with the new high-torque motors. (For example, Sherline Complete CNC systems, P/N 8760 CNC 4-axis driver box kit, or any of our CNC upgrade kits.)
ATTENTION: This new high-torque stepper motor requires a special CNC coupling (P/N 671052, sold separately).
NEW PRODUCTS (September 2017)
We have recently released a new set of 4″ rotary tables designed with our industrial users in mind. These industrial versions of Sherline rotary tables have a larger through-hole and a Nickel-Teflon plating on the table surface.
Our industrial customers wanted a rotary table that could hold larger stock and stand up to everyday use. The through-hole on these new rotary tables is 15/32″ (.469″) compared to our standard rotary tables which have a 5/16″ (.316″) through hole, and the Nickel-Teflon coating gives the table a rust-resistant surface that is hard and has added lubrication qualities.
The tables include a chuck adapter (P/N 37097) that has a 3/4-16 thread for the chuck and a 5/8-24 thread for the rotary table, and there is a .6485″ c’bore at the entrance of the 5/8-24 thread which is used to locate the adapter concentric to the rotary table. Like our standard rotary tables, they also include a set of two hold-down clamps and T-nuts for mounting to various surfaces.
Top row (l to r): 5932, 5937
Bottom row (l to r): 5931, 5936
Tools not included, shown for reference only.
NEW PRODUCTS (August 2017)
These new multi-tool holders were designed to complement our four position, gang-tooling tool posts (P/N 5930 or P/N 5935). They can be used in conjunction with the gang-tooling tool post, or on its own for our customers who want to convert their Sherline lathe into a “Chucker Lathe” or gang-tooling lathe.
The front-side tool holders hold up to two, round boring tools, and a slot for holding turning, grooving or threading tools. P/N 5932 has (2) 3/8″ holes to hold boring bars, drill chucks, or tool bushings, and a slot to hold a 3/8″ lathe cutting tool with two locking screws for each tool. We also offer a tool post (P/N 5937) that has (2) 5/8″ holes for those wanting to use ER16 collet holders with a 5/8″ shank.
The rear-side cutoff tool holders are similar to the front-side tool holders, but they have a slot for holding a cutoff tool blade (P/N 30860). Using the holder as a rear mounted cutoff tool allows you to use the cutoff tool from the back side of the part. P/N 5931 has 3/8″ holes, and P/N 5936 has 5/8″ holes.
ACCORDION WAY COVER UPGRADE (August 2017)
Mill Accordion Way Cover P/N 5090
Our way cover material has recently been upgraded. The new polypropylene material is more durable and is resilient enough to better withstand the temperature of hot chips. The material itself is more opaque and is 10 mil, versus the clear, 5 mil of the previous version (mil=0.001″).
The upgraded material offers a better value than our previous way covers because it will wear longer, and we are able to offer it without having to raise the price.
NEW WEB PAGE (August 2017)
Our Pool Cue Live Center (P/N 1182PC) has been such a success that we have created a new web page dedicated to Pool Cue Makers. In addition to the live center, there is information on custom pool cue lathes, videos, and related products. You can find the Pool Cue Makers page link in the sidebar menu.
NEW VIDEO (August 2017)
Not every job in the machine shop requires the use of large, expensive machines. You can free up some of your more expensive CNC machines by doing small jobs on benchtop CNC lathes and mills like those made by Sherline Products. Sherline’s CNC mills start at under $3,000. Lathes cost even less. This video shows actual parts we make for our lever collet closer (P/N 1150) being made on Sherline CNC machines. You can also find this video posted on our Videos page.
NEW CNC HELP DOCUMENT (August 2017)
This document includes sample G and M code, and suggestions for tool holders and setting up your tools. The PDF also includes links to external web CNC documentation and a YouTube Sherline tool video. The direct link to the PDF can also be found on the following page: CNC Instructions
NEW PRODUCT! (June 2017)
Aluminum Replacement Pie Jaws P/N 11454-4P
This replacement set of aluminum pie jaws, P/N 11454-4P, was designed to give our customers the option of pie jaws that are made from a softer material than our P/N 1143-4P steel replacement pie jaws. Because they are aluminum, they can be used with our 1076 chuck. However, we still recommend using them with our 1076C because of the hardness of the nickel and the lubricating properties of the Teflon.
The primary advantage of the aluminum jaws is that the aluminum is easier to machine, and it offers a material that will not scratch or dent softer parts.
NEW SHERLINE LASER DIVISION WEBSITE (May 2017)
Sherline recently launched a new website dedicated solely to our laser marking and scanning products. Each year our machines and accessories are being purchased for use in fields other than for which they were intended. We have developed a number of accessories to aid those in the lasering industries. These accessories include plates, tables, and jaws that help hold parts while being laser engraved or scanned.
NEW PRODUCT! (March 2017)
Pool Cue Live Center P/N 1182PC
We designed this center at the request of some of our customers who use our machines (or modifications of our machines) to make pool cues. They needed a live center with an extended nose, to give them room for their cutters. The extended nose allows them to start cutting from the tip of the pool cue without needing extra material to hold onto.
NEW PRODUCT! (February 2017)
Laser Engraving Tilting Angle Table P/N 3750-LAZ
We designed this tilting angle table for laser engraving because we realize that most laser engraving shops don’t have access to a machine shop that can make special fixtures for their parts. The table includes a dozen steel dowel pins for locating parts, and the bottom half of the holes are tapped so you can use hold-down clamps.
New from dPP Engineering Work with your Sherline controller seamlessly from your Windows®-based Laptop/Desktop USB port (1/6/17)
Use your own laptop or desktop via the USB port with Sherline’s CNC controller P/N 8760
This new controller supports both MACH3 and MACH4 software, whereas previous controllers were dedicated to one software or the other. Moreover, the execution speed is faster than before, especially for MACH4 users. Additional features, such as threading and gear cutting, are easier to implement (spindle speed decoders and PWM are required for the latter).
This USB device is designed specifically for use with CNC machines with existing LPT (parallel printer) port-based control signals input connector. It allows for a quick migration from the LPT to the USB bus. Although small, the device is adjustable and requires no complex knowledge of device programming.
Please visit discount.campus.com for more details regarding the price, features, and requirements of this item.
SHERLINE TO ATTEND 2017 CABIN FEVER EXPO IN LEBANON, PA (1/10/17)
For all of you planning to attend the 2017 Cabin Fever Expo January 14, 15 in Lebanon, PA, please visit Sherline’s booth (N25). We will be demonstrating our largest mill yet, the 5800 NexGen. If you are attending, don’t forget to ask about our Show Special. For more info on the expo, see the Cabin Fever website at www.cabinfeverexpo.com.
NEW PRODUCT! (January 2017)
5/8″ Gang-Tooling Tool Post P/N 5935
Our new 5/8″ gang-tooling tool post is similar to our 3/8″ gang-tooling tool post, but it allows customers to use ER16 collet holders with a 5/8″ shank. Like the 3/8″ holder, it also can also hold up to four tools with a known centerline-to-centerline distance of 1.500″.
NEW PRODUCT! (December 2016)
3/8″ Gang-Tooling Tool Post P/N 5930
Our new gang-tooling tool post was designed specifically for our customers who want to convert their Sherline lathe into a “Chucker Lathe” or gang-tooling lathe. The gang-tooling tool post offers a convenient and accurate way to hold up to four tools with a known centerline-to-centerline distance of 1.500″. This tool post has (4) 3/8″ holes to hold boring bars, drill chucks, or tool bushings with two locking screws for each tool (tools not included).
NEW PRODUCT! (December 2016)
4″ Reverse Rotary Table P/N 3700-OP
The reverse rotary table is perfect for using on the tilting angle table (P/N 3750). The reverse mount allows access to the handwheel from the front of the machine. If you used a standard rotary table in the previously described set-up the handwheel would be mounted facing the backside of the X-axis. It is also available in CNC-Ready configuration, P/N 3700-CNC-OP.
NEW PRODUCT! (December 2016)
Jack-in-a-Box Puzzle Kit P/N J1000
Here’s a fun project that you can make on your Sherline mill that will amaze your friends. When done, a tiny jack is contained inside a cube with a hole in it. How did they get in there? How was it made? Producing the finished cube requires a series of drilling and boring processes explained in the step-by-step illustrated instructions that come with the kit.
NEW PRODUCT! (October 2016)
5th-Wheel Trailer Hitch Weight Scale P/N LM5
We made this scale at the request of several of our customers who own fifth-wheel trailers. This scale is a modified version of our original Trailer Tongue Weight Scale. However, it is specifically designed to attach to most fifth-wheel trailer hitches. The piston has also been modified to accept the standard 2-13/16″ diameter kingpin, and the locating pin is for hitches that accept the standard 2-13/16″ kingpin.
Sherline Products is proud to announce its sponsorship of Duro UAS.
Duro builds “eco-drones” like the Harbor AUV, one of the first autonomous underwater vehicles dedicated to urban coastal mapping and environmental data collection. Students will be using a Sherline 2000 mill to make parts for the AUV. To learn more about Sherline’s collaboration with Duro UAS CLICK HERE, or to learn more about Duro UAS visit their website at durouas.com. You can also visit our new Engineering Support page to view more stories about how Sherline Products is being used in other educational and industrial settings.
NEW PRODUCT! (August 2016)
Our latest product is a 2″ Rigid-Column Spacer. These spacers are available in round and rectangular formats for the 2000-series mill and the 5400-series mill column bases with a 2000 ram, respectively. The round spacer on the left is designed to be used in conjunction with the 2000-series mill, while the rectangular spacer is meant to be used with either our Short and Tall 5400 Mill Column Bases with the 2000 Ram. Click the part number for product details on the round spacer P/N 56057 or here for the rectangular spacer P/N 50058.
Now available for Windows 10, 32b and 64b For Windows® users only (6/6/16)
Use your own laptop or desktop via the USB port with Sherline’s CNC controller P/N 8760
New from dPP Engineering is this new USB CNC to LPT motion controller. This product contains a microprocessor which simulates a complete CNC controller program and thus elevates the processing load from the host computer. It is 100% LPT port pin-out compatible. This product works with either Artsoft’s MACH4 CNC software. A similar product works with Artsoft’s MACH3 and UC-CNC. Visit discountcampus.com for more information.
NEW PRODUCT! (May 2016)
3C Collet Headstock P/N 30113
Many of our customers over the years have requested a spindle and collet that would allow larger diameter stock to go through the headstock. With the 3C collet, our customers can now hold stock up to 1/2″ diameter that will pass through the headstock. The 3C Collet Headstock includes a 1″ spindle wrench (shank and collet not included, shown for reference only).
SHERLINE TO ATTEND 2016 DMEDS IN DEL MAR, CA (5/4/16 – 5/5/16)
The DMEDS is the Del Mar Electronics & Design Show. This event is a design and manufacturing show open to the public for electronics, medical and biotech industries located in Southern California with over 65 FREE seminars.
The expo will be held at the Del Mar Fairgrounds, May 4-5, in the Bing Crosby and Exhibit Halls. We will be showing many of our new products and items from our industrial products division. Attendees must register, but admittance is FREE!
For more info on the expo, see the Del Mar Electronics & Design Show web site at www.mfgshow.com.
SHERLINE TO ATTEND 2016 NAMES EXPO IN WYANDOTTE, MI (4/21/16)
For all of you planning to attend the 2016 NAMES Expo April 23-24 in Wyandotte, please visit Sherline’s booth (58-61). We will be demonstrating our largest mill yet, the 5800 NexGen and more. For more info on the expo, see the North American Model Engineering Society web site at www.namesexposition.com/expo.
NEW PRODUCT! (February 2016)
Riser Plate for 8″ Crosslide P/N 1294
We designed the headstock riser plate P/N 12940 at the request of several of our customers who replaced our 6″ crosslide with the thicker 8″ crosslide P/N 60880 (manual) and P/N 67036 (CNC). Most of these customers are using our lathe as a chucker lathe with gang tooling. By using this riser plate, we have raised the headstock to match the additional thickness of the 8″ crosslide. Therefore, all of our standard tool posts will now be on centerline with the headstock.
NEW PRODUCT! (January 2016)
5400 Mill Column Base with 2000 Ram P/N 5640 (Short), P/N 5645 (Tall)
These rigid columns are designed for those who have a 5400-series mill. Each comes with the 2000-series ram and gives the versatility of Sherline’s 2000-series mill column with it’s large work area and seven directions of movement. The tall column provides more Z-clearance.
NEW PRODUCT! (January 2016)
Rigid Mill Column Bases for 2000 Mills P/N 5605 (Short), P/N 5606 (Tall)
For those who want the versatility of Sherline’s 2000/2010 mill column with it’s large work area and multiple directions of movement but have experienced unwanted column rotation during extreme machining loads on the 2000 mill, this new column offers another option. The one-piece column absolutely prevents that from happening, although you do give up the ability to rotate the column ram from side-to-side.
NEW PRODUCT! (November 2015)
NexGen Vertical Mill P/N 5800/5810
Starting in November, 2015 Sherline Products is proud to introduce its latest Vertical Milling machine. With the increase of popularity of Sherline mills in industrial, laboratory, and school training environments the need to produce larger parts has led to the development of an extended capacity milling machine. Sherline’s NexGen Mills are available in Manual, CNC-Ready, and full CNC configurations.
The new NexGen Mill has the following standard features:
- Extra-Rigid Column Base
- 15″ Extended Column Bed
- 18″ Extended Mill Table
- 18″ Mill Base
- 7″ x 13″ Tooling Plate (3 T-slots, Alignment Pins)
- Y-axis covers—Mill Accordion Way Cover Set and extended 12″ brass rear leadscrew cover
Other standard features include oilers on the X-, Y- and Z-axes to keep the column leadscrew and base saddle leadscrews and ways lubricated during extended CNC operations. In addition, backlash is adjustable on X-, Y- and Z-axes. Adjustable tapered plastic gibs provide a way to accommodate wear on the aluminum and steel dovetailed slides on all three axes.
NEW PRODUCT! (September 2015)
Lathe Headstock Hard Stop Kit P/N 40116
Starting in August, 2015 every Sherline headstock now includes the holes to add an optional hard stop. A hole through the headstock base allows the hard stop rod to be set to contact the lathe table, providing a hard stop for the Z axis during turning operations. For those who have an older Sherline lathe and want to add the hard stop, the kit includes instructions with dimensions on where your headstock case will need to be drilled to accept the rod and locking thumbscrew. Kit includes 4″ hard stop rod, 8″ hard stop rod and a 10-32 x 5/8” thumbscrew (lathe headstock purchased separately).
NEW PRODUCT! (June 17, 2015)
5C or ER collet to Sherline Chuck Arbors P/N 1065 and 1066
Install a Sherline 3-jaw or 4-jaw chuck in your full-size 1/2″ or 5/8″ lathe collet in seconds! These adapters have a straight shank that will slip into the collet and a 3/4-16 thread on the other end to hold any Sherline 2.5″ or 3.1″ chuck. Shanks are available to fit 1/2″ (P/N 10660) or 5/8″ collets (P/N 10650). When you are done with the job, just remove the chuck and arbor and go back to using your collets.